Do Old Flexible Ducts Need Replacing When You Upgrade a Ducted Heater?

No Australian law forces you to replace flexible ducts when you upgrade a ducted heater. The ducts only need replacing if they fall short of the standards that apply to your new system. Most ductwork over 15 years old fails at least one of those checks, which is why replacement ends up in the majority of upgrade quotes.

There is one situation where the answer is almost always yes. If you are switching from gas ducted heating to ducted reverse cycle, the minimum duct insulation rating usually rises from R1.0 to R1.5, and existing R1.0 ductwork no longer complies. At Heating Experts, this is the first thing our technicians check when quoting a ducted heater installation, because it changes the price of the job by thousands of dollars. The numbers behind that check are stark. An AIRAH field study by engineer Graham Palmer measured old ductwork in Melbourne homes losing between 26 and 58 percent of the heat the furnace produced. New ducts cut those losses to 10 to 18 per cent.

Is replacing your ductwork legally required in Australia?

There is no blanket rule that says old ducts must go when the heater does. The National Construction Code sets performance requirements that the ductwork serving a new system has to meet. If your existing ducts already meet them, and you can prove they meet them, reuse is allowed.

The catch is that those requirements are written for the system you are installing now, not the one you installed in 2004. A set of ducts that was legal under an older code, or that was never compliant to begin with, does not get grandfathered in just because it is already in the roof.

What R-value does flexible ductwork need in an Australian home?

For houses, the rules sit in NCC Housing Provisions clause 13.7.4. The minimum insulation R-value depends on two things. The first is the type of system you are running. The second is your climate zone.

System type

Climate zones 1, 3, 4, 6, 7

Climate zones 2 and 5

Climate zone 8

Heating only (gas ducted heater) or cooling only

R1.0

R1.0

R1.5

Combined heating and refrigerated cooling (ducted reverse cycle)

R1.5

R1.0

R1.5

Fittings, all system types

R0.4

R0.4

R0.4

Climate zones matter more than most homeowners expect. Melbourne sits in zone 6, and Canberra and Hobart in zone 7, so a ducted reverse cycle system in any of those cities needs R1.5 ductwork. Sydney, Adelaide and Perth are zone 5, and Brisbane is zone 2, where R1.0 still satisfies the minimum. Zones can change within a single metropolitan area, so check your address against the ABCB climate zone tables rather than assuming the capital city figure applies to the whole region.

The code also requires ductwork to be sealed against air loss, with all openings, joints and seams in the duct surface closed using adhesives, mastics, sealants or gaskets. Ducts and fittings inside the insulated building envelope are exempt from the insulation requirement. That exemption is why a short run through a conditioned space is treated differently from a long run across a hot roof space.

Why a reverse cycle upgrade usually means new ductwork

Most of the calls we take about duct replacement come from homeowners swapping a gas ducted heater for ducted reverse cycle. Two things change at once.

The first is the R-value. A reverse cycle system is classed as a combined heating and refrigerated cooling system, which pushes the minimum from R1.0 to R1.5 across zones 1, 3, 4, 6, 7 and 8. Gas ducted systems were generally installed to the R1.0 minimum that applied to them, so the existing ductwork usually falls short of R1.5.

The second is airflow. Gas heaters run at a lower airflow because the air picks up more heat on each pass through the heat exchanger. A reverse cycle system has to move considerably more air to deliver both heating and cooling. Ducts sized for a gas heater often cannot supply that volume without the blower working against high static pressure, which shows up as weak outlets, noise and higher power draw. The same mechanism explains a ducted system not warming the back rooms, and a higher-airflow unit on undersized runs makes it worse.

If you are replacing a gas heater with another gas heater of similar capacity, neither problem applies. The R1.0 minimum still stands, the airflow demand is comparable, and reuse is far more likely to be viable.

How do old flexible ducts fail?

Roof spaces are hard on flexible duct. Summer cavity temperatures, UV through tile gaps, rodents and decades of tradespeople crawling past all take a toll. These are the failures we find most often when we pull a vent grille and look up the run.

  • Crushed or compressed insulation. The blanket only delivers its rated R-value at its rated thickness. Where a duct has been squashed under a beam or flattened by a foot, the insulation in that section performs well below its label.
  • Sagging and excess length. Duct left long and draped between joists adds resistance and cuts the airflow reaching the outlet. Every unnecessary sag and bend costs pressure the blower has to make up.
  • Torn liner and broken helix. Once the inner liner splits or the support wire breaks, the duct cannot hold its shape or its pressure rating.
  • Separated collars and failed tape. Old duct tape dries out and lets go at the plenum and at ceiling boxes, dumping heated air straight into the roof.
  • Dust, droppings and moisture. Mould and rodent contamination cannot be reliably cleaned out of a flexible liner, so contaminated duct gets discarded.

Measured results matter more than a visual check. Duct in the pre-retrofit homes in that study came in at roughly R0.6, well under the R1.0 those systems were meant to have. Palmer also found little additional benefit above R1.5, which lines up with where the code and the state incentive schemes have landed.

Should you reuse or replace your old flexible ducts?

We work through the same list on every upgrade quote. Reuse is only on the table when every row on the left is satisfied. A single item in the right-hand column is enough to put a new duct in the quote.

What we check

Reuse is viable when

Replace when

Insulation rating

Duct is labelled or documented at or above the R-value your new system requires

Rating is below the minimum, unknown, or the label has perished

Insulation condition

Blanket is at full thickness, dry and intact along the whole run

Sections are crushed, flattened, wet or missing

Liner and helix

Inner liner is unbroken and the support wire is fully helixed

Tears, splits, a crumbling liner, or a collapsed helix

Joints and collars

Every collar is banded and sealed, and seams hold under pressure

Open seams, failed tape, or duct pulled off the plenum

Hygiene

Light surface dust only

Visible mould, water staining, or rodent evidence

Sizing and layout

Diameters and run lengths suit the new unit's airflow in litres per second

New unit needs materially more air, or the layout is changing for new zones

Age

Under roughly 15 years and verifiably compliant

Over 15 years, or no documentation of what was installed

Ask your installer for supply and return airflow readings and static pressure at the fan. A visual inspection from the manhole will miss leaks that smoke testing or pressure testing finds in minutes.

Is replacing the ductwork worth the money?

Duct replacement adds to the cost of an upgrade, and it is fair to ask whether it pays for itself. Palmer put the average payback at nine years for systems over 15 years old, with efficiency improving by an average of 30 per cent for that age group and 14 per cent for systems under 15 years. That research dates from 2009, so it predates current energy prices.

Rebates change the maths further. Victoria's heating and cooling discounts offer up to $5,530 off when a ducted gas heater is replaced with an efficient reverse cycle system, which can offset the cost of new ductwork. South Australia takes a more direct approach. The REES efficient ductwork activity defines thermally efficient ductwork as flexible duct insulated to R1.5 or R2.0, and pays an incentive for installing it on either a ducted reverse cycle unit or a gas ducted central heater.

Both schemes point the same direction. Where the code sets R1.5 as a floor, the incentive programs treat R1.5 and R2.0 as the target. Going one step above the minimum costs very little extra while the roof space is already open. For a fuller picture of what an upgrade runs in total, our breakdown of ducted heating installation costs covers the other line items.

Frequently asked questions

Can old flexible ducts be cleaned instead of replaced?

Light surface dust inside an otherwise sound duct can be cleaned, and the grille filters and return plenum should be cleaned on any new install. Mould and rodent contamination are different. Spores bind to the flexible liner and inner blanket in ways cleaning does not fully resolve, so contaminated flexible duct gets replaced.

How long do flexible ducts last in an Australian roof space?

Flexible duct in a roof space generally gives 15 to 20 years of reliable service. Beyond that, leakage climbs sharply. Palmer's field data showed leakage above 20 per cent in systems over 25 years old, roughly double the 5 to 10 per cent measured on ten year old systems.

Do I need new ducts if I replace a gas heater with another gas heater?

Usually not. A like-for-like gas replacement keeps the same R1.0 minimum in climate zones 1 to 7 and similar airflow requirements, so compliant ducts in good condition can be reused. Have the runs inspected and pressure tested before the old unit comes out, because that is the cheapest moment to fix anything.

Can I reuse existing ducts if I am adding zoning?

Only if the existing runs can deliver the airflow each zone needs when the other zones are closed. Zoning concentrates air into fewer outlets and raises static pressure on those runs. Older layouts frequently need re-sizing or additional runs, which we cover in our guide to zoning an older ducted system.

What documentation should I ask for if I am reusing ducts?

Ask for the manufacturer's R-value documentation for the installed duct, confirmation that it complies with AS 4254.1 for flexible duct, and commissioning results showing measured airflow and static pressure on the new system. If your installer cannot produce evidence of the duct's rating, the safe assumption is that it does not meet the current minimum.

Get your existing ductwork assessed before you commit

The answer to this question depends on what is actually in your roof, and establishing that takes a torch, a manometer and a look along the full length of each run. Before you sign off on an upgrade quote, make sure the ductwork has been inspected, measured and pressure tested.

Our technicians work in all capital cities, surrounding suburbs and regional areas, and we assess existing ductwork as part of every ducted upgrade quote. Book an inspection with Heating Experts and we will tell you in writing whether your ducts can stay, before any work starts.